In this article8 sections
- Who sets the rules in BC
- What RMS is, and why it comes up in BC
- How BC measurements usually work for detached homes
- Strata lots: the plan number isn't always the living area
- What can go wrong
- What a LiDAR floor plan shows, and what it doesn't
- A checklist before the size goes on the listing
- Where floor plans fit in the listing
BC has no single mandatory method for measuring a home for a listing. Alberta's Residential Measurement Standard (RMS) is the law for Alberta licensees, not BC ones. In BC, BCFSA says more than one standard can be used, as long as the listing agent measures consistently and can explain what the number includes. A floor plan shows layout and room sizes; the square footage on the listing is a separate decision.
This guide is for Metro Vancouver realtors who order floor plans and have to put a size on an MLS listing. It explains what the BC regulator says, what RMS actually is, and where a scanned floor plan helps and where it doesn't. The guidance below is as of November 2026; follow the linked BCFSA and RECA pages for the current wording.
Who sets the rules in BC
Real estate licensees in BC are regulated by the BC Financial Services Authority (BCFSA). Its practice resource on property measurements opens with a warning: inaccurate measurement is a common reason for complaints, and caution is recommended for every property type.
The same page says plainly that "there is more than one standard that can be applied." What it asks for is consistency with how measuring is usually done for that market and that type of property. It also notes that some agents hire a company that specializes in measuring as part of their due diligence on a new listing.
So the BC rule isn't "use method X." The rule is that the size you advertise must be honest, measured with reasonable care, and explainable.
What RMS is, and why it comes up in BC
RMS was created by the Real Estate Council of Alberta (RECA). On its Residential Measurement Standard page, RECA states that Alberta residential licensees must use RMS when they measure and advertise residential properties. Its principles include:
- the RMS size must be calculated to within 2%
- detached homes and townhouses are measured from the exterior walls at the foundation
- apartment-style condos are measured from the interior perimeter walls, paint to paint
- any floor level that is partly below grade is excluded from the RMS area (it can be measured and shown separately)
- space counts only where the ceiling is at least 2.13 m (7 ft); under a sloped ceiling, the area with at least 1.52 m (5 ft) of headroom counts if the room reaches 7 ft somewhere
- open-to-below areas, such as vaulted spaces, are excluded
You see "RMS" in BC because many measuring and floor plan companies across Canada use these principles as their method. That is a reasonable, well-documented approach. But in BC it is a choice of method, not a legal requirement, and an RMS figure can be noticeably smaller than a BC figure that includes a finished basement.
How BC measurements usually work for detached homes
BCFSA's practice resource gives one common standard as an example, not as a mandate:
- Floor area is based on the exterior dimensions of the building at each floor level and includes interior walls. For attached units, the outside dimension is the centre line of the shared wall. Garages within the footprint are netted out.
- Finished area is space suitable for year-round use, with walls, floors and ceilings similar to the rest of the house. Measurements are taken to the nearest inch or tenth of a foot, and the area is reported to the nearest square foot. Garages are excluded.
BCFSA names the areas that cause the most trouble: oddly shaped rooms, upper-floor rooms under a sloping roof, and basements. Those are exactly where Metro Vancouver housing gets complicated. Think of a North Shore split-level built into a slope, a character house with a half-storey under the roof, or a Port Coquitlam home with a basement suite. Our post on floor plans for sloped-lot homes in North Vancouver shows how much a layout can hide on those properties.
For room sizes, the resource lists the rooms that are normally measured: bedrooms, living room, dining room, kitchen, eating area, family room, den and special-use rooms like a laundry room or a finished, heated workshop. Bathrooms, hallways, foyers and stairs usually aren't measured unless they are large or a feature of the house.
Strata lots: the plan number isn't always the living area
Condos and townhouses add a second source of error. The square area shown on a strata plan at the Land Title Office can include balconies, patios, carports or storage rooms. BCFSA says some plans carry a note to the effect that areas shown are total areas including those spaces, and in that case the agent should find the figures for the included areas and deduct them.
BCFSA also says strata plan measurements have occasionally turned out to be wrong, for example when a builder departed from the filed plans during construction, and that agents should check them by physically measuring the unit.
Its suggested wording keeps the strata lot and the extras separate, along the lines of: a strata lot of 1,400 square feet plus the exclusive use of a balcony, patio and two parking spaces designated as limited common property. That tells a buyer exactly what is being offered. For tower-heavy markets like Burnaby, where many listings are strata units, this distinction comes up on almost every listing.
What can go wrong
BCFSA's advertising guidelines include a case about square footage. An MLS listing gave the home's size as 1,375 square feet. After the sale closed, the buyers' insurer told them it was about 1,000 square feet. The case lists contraventions of the rules requiring licensees to act honestly and with reasonable care and skill, and prohibiting false or misleading advertising.
The lesson isn't that one method is right and another is wrong. It's that a number nobody can explain, or one copied from an old listing or a plan without checking, is the risk.
What a LiDAR floor plan shows, and what it doesn't
A floor plan made from a LiDAR scan records the interior of the home: walls, doors, windows, stairs and the shape of each room. From that, the plan shows:
- the layout and how rooms connect
- room dimensions and labels
- level-by-level drawings, including basements and lofts
- the shape of awkward rooms that photos make hard to read
What a scan can't settle on its own is which method the listing should use. A scanner inside the home sees interior surfaces, so an exterior-based total has to add the thickness of the outside walls, either measured or assumed. Which levels and spaces count, how to treat sloped ceilings, and whether a suite or an unfinished room is included are decisions about method. They need to match what the listing says.
Two practical habits help:
- Ask which totals appear on the plan. A plan might show interior area per floor, an exterior-based total, or both, and it should say which.
- Write down the method in your file. If a buyer's agent asks how the size was arrived at, you can answer in one sentence: for example, exterior measurement of all finished above-grade levels, basement measured separately.
A checklist before the size goes on the listing
- Decide the method first (exterior or interior, which levels count, how below-grade space is shown).
- For strata units, compare your figure with the strata plan and look for notes that it includes balconies, patios or parking.
- Show limited common property separately rather than adding it to the unit's area.
- Treat sloped ceilings, basements and odd-shaped rooms with extra care; these are BCFSA's named trouble spots.
- Keep the floor plan, the measurement notes and the source of the figure in the listing file.
- If you use RMS, say so, and remember a buyer comparing it with a BC listing that includes the basement may see a lower number.
Where floor plans fit in the listing
Buyers use floor plans to read a home's layout before they book a showing, and a clear plan also gives you a documented record of the rooms you measured. If you want photos tied to the plan, our guide to Floor View Tours explains how pinning photos to the plan helps buyers follow the layout.
RealtyShot offers LiDAR floor plans alongside HDR photography, video tours and 3D tours. See what each service includes on the services page, and compare packages on the pricing page.
Further reading

Written by
RealtyShot
Real estate photography, 3D tours, drone and video for agents across Metro Vancouver. Based in North Vancouver and shooting from Vancouver to the Fraser Valley for 5+ years.
Book with RealtyShot
Book your listing media
Pick a package or individual services, choose a time and get an instant price in the booking portal.
Packages from $299
30% OFF30% off for everyone, extra 20% on your first order 604-600-1317











